Clearone Beamforming Microphone Array Installation Guide Manual do Utilizador

Beamforming Microphone ArrayGroup Microphone for Professional ConferencingInstallatIon GuIde

7 Beamforming Microphone ArraySlide the Trim Plate onto the bottom of the Suspension Column extending through the ceiling tile. This must be done

Chapter 2: Ceiling Mount Installation 8Drop-Ceiling TileCeiling Plate, Suspension Column, Trim Plate and Mic Mounting PlateAssembled in Drop-Ceili

9 Beamforming Microphone ArrayLift the assembly, along with the ceiling tile, into place in the drop-ceiling support framework.Install the Support

Chapter 2: Ceiling Mount Installation 10Pass the E-bus cables for LINK IN and LINK OUT (if needed), and the PoE cable from above the ceiling throu

11 Beamforming Microphone ArraySlide Beamforming Microphone Array UP & OVER Keyhole Slots(E-bus and PoE Cables Not Shown)HEInstall fourth scre

Chapter 2: Ceiling Mount Installation 12 » NOTE: After the Beamforming Microphone Array is mounted, you might need to tilt the array to make it le

13 Beamforming Microphone ArraySOLID-CEILING MOUNTING PROCEDUREUse the following dimensions for the cable pass-through cut-out for the solid-ceili

Chapter 2: Ceiling Mount Installation 14Slide the Trim Plate onto the bottom of the Suspension Column. This must be done before fastening the Mic

15 Beamforming Microphone ArrayPass the E-bus cables for LINK IN and LINK OUT (if needed), and the PoE cable from above the ceiling through the pa

Chapter 2: Ceiling Mount Installation 16HE3XCable Retention ClipsNOTE: ONLY INSERT SCREWS PARTIALLYUse #1 Phillips screwdriver bit to avoid damagi

ClearOne 5225 Wiley Post WaySuite 500Salt Lake City, UT 84116Telephone 1.800.283.5936 1.801.974.3760Tech Sales 1.800.705.2103FAX 1.801.974.36

17 Beamforming Microphone ArrayChapter 3: Wall Mount InstallationOnce you have verified all the firmware updates and necessary connections made wh

Chapter 3: Wall Mount Installation 18WALL MOUNTING PROCEDUREThe wall mounted Beamforming Microphone Array must be placed on a wall facing the inte

19 Beamforming Microphone ArrayLocate, level and mark for drill holes and the cable pass-through cut-out where the Wall Mounting Plate will attach

Chapter 3: Wall Mount Installation 20Notice that the Mic Mounting Plate (C) has four holes used for mounting to the back of the Beamforming Microp

21 Beamforming Microphone ArrayFor mountings with the cables coming in front of the wall, hold the Beamforming Microphone Array with the Mic Mount

Chapter 3: Wall Mount Installation 22Front View of Mic Mounting Plate over Wall Mounting Plate (Beamforming Microphone Array and cables not shown.

23 Beamforming Microphone ArrayChapter 4: Table Top InstallationOnce you have verified all the firmware updates and necessary connections made whi

Chapter 4: Table Top Installation 24usageWhen the table top installation of the Beamforming Microphone Array is completed, use the CONVERGE Consol

25 Beamforming Microphone ArrayService and SupportIf you need assistance setting up or operating your product, please contact us. We welcome your

Chapter 1: Getting Started ...1SKU’s Used ...

1 Beamforming Microphone ArrayChapter 1: Getting StartedCongratulations on purchasing your Beamforming Microphone Array. The Beamforming Microphon

Chapter 1: Getting Started 2 » NOTE: The PoE connection is only for power, not control. Power must be supplied to individual units; no daisy-chain

3 Beamforming Microphone ArrayThe Beamforming Microphone Array is connected to the CONVERGE Pro and to other Beamforming Microphone Array units vi

Chapter 2: Ceiling Mount Installation 4Chapter 2: Ceiling Mount InstallationOnce you have verified all the firmware updates and necessary connecti

5 Beamforming Microphone ArrayTOOLS REQUIREDThe following tools are required for installation of the Beamforming Microphone Array.DROP-CEILING MOU

Chapter 2: Ceiling Mount Installation 6Use the screws to fasten the Ceiling Mounting Plate to the top of the Suspension Column. Place the plate on