ClearOne AP10 Especificações descarregar pdf (Página 10)

Technical or Setup Assistance

Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • http://www.gentner.com

Page 6 Audio Perfect

10 Installation and Operations Manual

G-LINK NETWORK NOTE:

If the Gentner units to be networked are stacked vertically, connect them using the

short RJ45 jumper (provided). If networking Gentner units (maximum distance 20

feet between units), Gentner Communications recommends that category five twisted-

pair (10BaseT LAN) cable be used.

The first Gentner unit in the chain must have the G-LINK IN connector [2]

terminated with a G-Link terminator (provided). The first Gentner unit’s G-

LINK OUT connector [3] is then attached to the G-LINK IN [2] connector on

the next unit in the chain. At the end of the network, the final unit must have the

G-LINK OUT connector [3] terminated with a G-Link terminator as well. A G-

Link network will allow interconnection of up to 16 AP10s and eight AP800s.

Step 5 — Device ID (Dip Switches 9–12)

Once your physical G-Link network is established, you need to set up unique G-

Link device ID numbers for each AP10 on the network. As shipped from the

factory, all AP10 units default as binary address 0. Set Device ID numbers for

each Gentner unit at your site by manipulating front-panel dip switches 9–12,

selecting/deselecting each switch to set up address 0–15 in binary code. Table 1

(below) illustrates how this is done.

Set the device ID for each AP product on the G-Link network.

DEVICE ID CONFLICT ERROR NOTE:

If more than one AP10 is assigned the same device ID number, the TRANSMIT and

RECEIVE LEDs will flash back and forth on the affected units until the error is

corrected.

Installation

Continued

Figure 10. AP10 power module

Step 6 — Power Connection

The power cord [1] (See Figure 10, left) will operate at any level between 100–

240Vac, 50–60Hz, 30W.

Hardware installation is now complete.

Table 1. Device ID Dip

Switch Settings

Binary Dip Switch 9 Dip Switch 10 Dip Switch 11 Dip Switch 12

Address Position Position Position Poisition

0 0 (DOWN) 0 (DOWN) 0 (DOWN) 0 (DOWN)

1 0 (DOWN) 0 (DOWN) 0 (DOWN) 1 (UP)

2 0 (DOWN) 0 (DOWN) 1 (UP) 0 (DOWN)

3 0 (DOWN) 0 (DOWN) 1 (UP) 1 (UP)

4 0 (DOWN) 1 (UP) 0 (DOWN) 0 (DOWN)

5 0 (DOWN) 1 (UP) 0 (DOWN) 1 (UP)

6 0 (DOWN) 1 (UP) 1 (UP) 0 (DOWN)

7 0 (DOWN) 1 (UP) 1 (UP) 1 (UP)

8 1 (UP) 0 (DOWN) 0 (DOWN) 0 (DOWN)

9 1 (UP) 0 (DOWN) 0 (DOWN) 1 (UP)

10 (A) 1 (UP) 0 (DOWN) 1 (UP) 0 (DOWN)

11 (B) 1 (UP) 0 (DOWN) 1 (UP) 1 (UP)

12 (C) 1 (UP) 1 (UP) 0 (DOWN) 0 (DOWN)

13 (D) 1 (UP) 1 (UP) 0 (DOWN) 1 (UP)

14 (E) 1 (UP) 1 (UP) 1 (UP) 0 (DOWN)

15 (F) 1 (UP) 1 (UP) 1 (UP) 1 (UP)

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 29 30

Comentários a estes Manuais

Sem comentários

ClearOne AP10 Especificações Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com Redes ClearOne AP10